Request Appointment

 

 

They are making several good annotation on the subject of How to Install a Bathtub overall in this great article underneath.

Setting up a tub isn't exactly brain surgery, yet it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately tough job. If the old bathtub is easily available, the task can relocate quickly; if you need to open a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make certain you have certified yourself for the work and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This article will aid you set up a brand-new bathtub in your shower room if you have already bought a brand-new tub as well as don't require to change the plan of your previous supply of water pipelines.
Your tools and also material list should make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Planning for the Installation

To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the tap includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.

 

 

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic due to the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Tub

Utilizing the two wood boards under its feet, position the tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To install faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bath tub as well as also examine the overflow outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of at least when as this will resolve it into its last position.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in problems with moisture and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water resistant adhesive and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We had been brought to that editorial about A Step-by-Step Guide to Installing a Bathtub through an associate on another web property. Enjoyed reading our blog? Please share it. Let another person check it out. Many thanks for your time. Please check up our site back soon.

Details